Masimo Radical Signal Extraction Instrukcja Operatora Pobierz pdf (Strona 36)

4-30 Radical-7 Color Display Signal Extraction Pulse Oximeter Operator’s Manual Rad-8 Signal Extraction Pulse Oximeter Operator’s Manual 5-1

alarms and messages

System Messages

The following chart alphabetically lists all system messages displayed on the LCD screen.

The cause of the message, and the action(s) to be taken are also shown.

The operator should become thoroughly familiar with this information before using the

oximeter for patient monitoring.

MESSAGE POSSIBLE CAUSE(S) RECOMMENDATION

AMBIENT LIGHT

Too much light on patient

(sensor). Inadequate

tissue covering sensor

detector.

Remove or reduce lighting. Cover sensor

from light. Reposition sensor..

CABLE LIFE EXP

Cable is no longer use-

able.

Replace with new or operable cable.

DEFECTIVE CABLE

Oximeter cannot identify

the connected cable or the

cable has failed.

Inoperative or faulty cable; Replace cable.

Refer to the Directions for Use of the cable

being used.

DEFECTIVE

SENSOR

Oximeter cannot identify

the connected sensor or

the sensor has failed.

Broken sensor cable wire or inoperative

LEDs or faulty detector; Replace sensor.

Refer to the instructions for the sensor being

used.

EMITTER RANGE

The temperature of the

emitter is outside of the

designed range.

Disconnect and reconnect the sensor. If the

message continues to display, replace the

sensor.

INCOMPATIBLE

SENSOR

Not a proper Masimo

sensor.

Replace with a proper Masimo sensor. Refer

to Section 8.

INTERFERENCE

Outside signal or energy

preventing reading.

Remove outside interference.

INVALID SENSOR

Oximeter cannot identify

the connected sensor.

Broken sensor cable wire or inoperative

LEDs or faulty detector; the sensor has

failed. Replace sensor. Refer to the instruc-

tions for the sensor being used.

LOW BATTERY

Battery charge is low.

Charge battery by placing the Radical-7

Handheld into the Docking Station and pow-

ering the unit with AC line power. Replace

battery if necessary.

LOW PERFUSION

Signal too small.

Move sensor to better perfused site. Refer to

Section 4, Low Perfusion.

LOW SIGNAL IQ

Low signal quality.

Ensure proper sensor application. Move

sensor to a better perfused site. Refer to

Section 4, Signal IQ.

LOW SpCO CONF

SpCo measurement

reading is obscured.

Ensure proper sensor application. Check

sensor to see if it is working properly. If not,

replace the sensor

LOW SpMet CONF

SpMet measurement

reading is obscured.

Ensure proper sensor application. Check

sensor to see if it is working properly. If not,

replace the sensor

operation

■ ONLY USE A SATSHARE CABLE THAT HAS A FERRITE BEAD INSTALLED.

■ SPMET, SPCO AND PI CANNOT BE DISPLAYED ON THE MULTIPARAMETER

MONITOR WITH SATSHARE.

To return from SatShare operation to normal standalone operation, simply disconnect

the SatShare cable from the patient monitor or disconnect the SatShare cable from the

SatShare connector on the back of the Radical-7 Pulse CO-Oximeter.

Home Mode Operation

The Radical-7 Pulse CO-Oximeter can be placed into the Home Mode to protect unquali-

fied users from changing the Radical-7 Pulse CO-Oximeter alarm settings and operation.

Entering a password does not automatically reset the Radical-7 Pulse CO-Oximeter to the

Normal operating mode. In the Home Mode, a password is required to access the menu

system and the touch key control buttons and icons.

NOTE: When the Radical-7 Pulse CO-Oximeter is set to operate in the Home mode the

default values that the Radical-7 reverts to after a power cycle are set according to

Section 3, Monitor Setup, with the exception of the Alarm Silence setting, which is

set to the pre-power down setting.

Password Operation

The Radical-7 Pulse CO-Oximeter password is 2-3-1. To enter the password use the touch-

key control buttons to the right or bottom of the LCD display and press the buttons in the

sequence shown in the following figure:

XX X

Then press 

3 3

First press 

2 2 2

1 1

Finally press 

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 54 55

Komentarze do niniejszej Instrukcji

Brak uwag

Masimo Radical Signal Extraction Instrukcja Operatora Strona 36

Komentarze do niniejszej Instrukcji